Frequently Asked Questions

Both 4-pin and 7-blade connectors work with all Kody bike rack lights. Here's how to choose: 4-PIN FLAT CONNECTOR The 4-pin flat connector is standard on most cars and SUVs. It powers your tail lights, brake lights, and turn signals — everything you need for a complete Kody light setup. 7-BLADE ROUND CONNECTOR The 7-blade connector is standard on most trucks and RVs. It powers everything the 4-pin does, plus: Reverse lights (available on select Medium and Large Kody lights) An integrated license plate light connection (what we call "plate ready") A heavier duty cable — no adapters needed HOW TO IDENTIFY WHAT YOU HAVE Check under your rear bumper near your hitch: Flat rectangle with 4 holes = 4-pin flat Round plug with 7 pins = 7-blade NEED TO UPGRADE OR SWITCH? A simple 4-pin to 7-blade adapter is available at most auto parts stores. If you'd like a replacement cable with a different connector, contact us. See our full Trailer Wiring & Connector Guide for more information.

We have three cable lengths available; Short (70"), Long (116") and Extra Long (164"). Short - The cable is 70" long. This is long enough to connect the light across most four bike racks plus a little slack. We also sell 60" extensions that can be used if needed to cover extra length from hitch extensions or swing out racks. Long - The cable is 116" long. This is long enough to route across the entire rack plus hitch extensions and most swing arms with a two bike rack. Extra Long - The cable is 164" long and can handle everything including a large four bike rack with a large pivot. It's best to measure your set up from where the light is installed to the connection on your vehicle to determine which cable length will fit.

The Kody Tech reverse light synchronizes with your vehicles existing reverse lights. It requires a seven blade trailer connection to obtain the reverse light signal. We have two reverse light options; an add on reverse light and a built in reverse light. Both reverse options are super bright to light up the space behind you and are excellent at communicating that you're in reverse and need the space cleared. The built in reverse light is only available on the Medium Size Double Lights and Large Size Double 16" Lights. The reverse is built into the main brake/tail/turn light. Both of the double lights will include the reverse light. The add on reverse lights are available on single pivoting lights and the double 16" sequencing lights. This light is a separate light fixture mounted to the main light bracket and wired into the seven blade cable.

This is called hyperflash. Your vehicle's electronics detect the LED trailer light as a fault (because LEDs draw much less current than old incandescent bulbs) and trigger the turn signal relay at double speed. THE FIX Install a load resistor on your trailer connector. This adds enough resistance to mimic an incandescent bulb and stops the hyperflash. No wiring knowledge required. • We sell resistor kits compatible with Kody lights • Installation uses simple wire taps — no cutting required • Takes about 15–20 minutes Contact us to order a resistor kit or if you need help selecting the right one for your setup.

Yes — with one important note about sequential (animated) turn signals. Tesla vehicles and some newer Ford models (2016+) can interfere with the sequential turn signal animation due to how their electronics monitor trailer load. The lights will still work — tail lights, brake lights, and turn signals all function correctly. OUR RECOMMENDATION Choose a non-sequential light option for Tesla and newer Fords. You get the same bright tail, brake, and turn signals — just without the animated sweep effect. If you already have a sequential light and are experiencing issues, contact us. We may be able to help with a resistor or other solution.

Yes. You have two options: OPTION 1 — USE AN ADAPTER (Easiest) A 4-pin to 7-blade adapter is available at most auto parts stores (O'Reilly, AutoZone, etc.) or online for ~$10–20. Simple plug-and-play — no installation required. OPTION 2 — REPLACE THE CABLE We sell replacement cables with 7-blade connectors. Contact us to order one for your specific Kody light model. Note: A 7-blade connection is required to use the reverse light option, which is available on select Medium and Large Kody lights only.